بدائل البحث:
_ wet » _ west (توسيع البحث)
decrease » increase (توسيع البحث)
يعرض 1 - 20 نتائج من 997 نتيجة بحث عن '(( 10 i decrease ) OR ((( _ wet decrease ) OR ((( 5 ht decrease ) OR ( _ 3d decrease ))))))*', وقت الاستعلام: 0.21s تنقيح النتائج
  1. 1

    The trans-10, cis-12 isomer of conjugated linoleic acid decreases adiponectin assembly by PPARγ-dependent and PPARγ-independent mechanisms حسب Miller, Jessica R.

    منشور في 2008
    "…The aim of this study was to determine whether the effects of t-10, c-12 CLA on adiponectin and TG are mediated through modulation of the transcription factor peroxisome proliferator-activated receptor γ (PPARγ). 3T3-L1 cells were treated either during or after differentiation into adipocytes with 100 μM t-10, c-12 CLA with or without 10 μM troglitazone, a PPARγ agonist, or 1 μM GW9662, a PPARγ antagonist, and adiponectin and TG levels were analyzed. …"
    احصل على النص الكامل
    article
  2. 2

    Magnesium-reinforced PMMA composite scaffolds: Synthesis, characterization, and 3D printing <i>via</i> stereolithography حسب Ambreen Afridi (22224310)

    منشور في 2025
    "…Notably, pure PMMA exhibited the highest tensile strength, 26.23 ± 0.14 MPa and an elastic modulus of 707.81 MPa, while PMMA resin/1% Mg showed the lowest strength (19.46 ± 0.25 MPa) and modulus (392.88 MPa), indicating a decrease in mechanical integrity with higher Mg content. …"
  3. 3
  4. 4
  5. 5

    Decreased methylglyoxal-mediated protein glycation in the healthy aging mouse model of ectopic expression of UCP1 in skeletal muscle حسب Jinit Masania (7164239)

    منشور في 2023
    "…Decreased formation and increased clearance of MG-derived AGEs may be associated with healthy aging in the HSA-mUCP1 mouse.…"
  6. 6
  7. 7
  8. 8
  9. 9

    Decreased Interfacial Dynamics Caused by the N501Y Mutation in the SARS-CoV-2 S1 Spike:ACE2 Complex حسب Wesam S. Ahmed (10170053)

    منشور في 2022
    "…</p><p dir="ltr">Corrigendum: Decreased interfacial dynamics caused by the N501Y mutation in the SARS-CoV-2 S1 spike:ACE2 complex: Frontiers in Molecular Biosciences: <a href="https://dx.doi.org/10.3389/fmolb.2022.1018464" rel="noreferrer" target="_blank">https://dx.doi.org/10.3389/fmolb.2022.1018464</a>, published online 19 October 2022.…"
  10. 10
  11. 11
  12. 12

    Corrigendum: Decreased interfacial dynamics caused by the N501Y mutation in the SARS-CoV-2 S1 spike:ACE2 complex حسب Wesam S. Ahmed (10170053)

    منشور في 2022
    "…<p dir="ltr">Corrigendum: Decreased interfacial dynamics caused by the N501Y mutation in the SARS-CoV-2 S1 spike:ACE2 complex: Frontiers in Molecular Biosciences <a href="https://dx.doi.org/10.3389/fmolb.2022.846996" target="_blank">https://dx.doi.org/10.3389/fmolb.2022.846996</a>, published online 22 July 2022.…"
  13. 13
  14. 14
  15. 15

    Environmental Footprint and Economics of a Full-Scale 3D-Printed House حسب Abdalla, Hadeer

    منشور في 2021
    "…The conventional construction method had higher impacts when compared to the 3D printing method with global warming potential of 1154.20 and 608.55 kg CO2 eq, non-carcinogenic toxicity 675.10 and 11.9 kg 1,4-DCB, and water consumption 233.35 and 183.95 m3, respectively. …"
    احصل على النص الكامل
    article
  16. 16

    3D Tissue-Engineered Vascular Drug Screening Platforms: Promise and Considerations حسب Isra Marei (11312895)

    منشور في 2022
    "…A novel approach is to develop 3D tissue engineered miniaturized constructs in vitro that are based on human cells. …"
  17. 17

    An additive manufacturing approach based on electrohydrodynamic printing to fabricate P3HT:PCBM thin films حسب Zulfikre Esa (19457344)

    منشور في 2023
    "…The root-mean-square roughness was found to vary significantly with the annealing temperature and the flow rate and ranged from 1.938 to 3.345 nm. The estimated film mass and thickness were found between 3.235 and 23.471 mg and 597.5 nm to 1.60 µm, respectively. …"
  18. 18

    3D printing of circular materials: Comparative environmental analysis of materials and construction techniques حسب Shoukat Alim Khan (14778226)

    منشور في 2023
    "…<p>The use of 3D printing in construction activities can help to reduce waste, lower energy consumption, and minimize the environmental impact of building projects. …"
  19. 19
  20. 20

    10-Day structured initiation protocol from multiple daily injection to hybrid closed-loop system in children and adolescents with type 1 diabetes حسب Goran Petrovski (129836)

    منشور في 2020
    "…<h3>Aim</h3><p dir="ltr">The aim of this study was to evaluate the 10-day initiation protocol for MiniMed 670G hybrid closed-loop (HCL) system in individuals with type 1 diabetes on multiple daily injection (MDI) in achieving desirable glycemic control.…"