Simulation and experimental study of underwater dissimilar friction-stir welding between aluminium and steel by Eyvazian, Arameh

“…The volume of fluid (VOF) modeling method was implemented to simulate the underwaterfriction-stir welding (FSW) process for dissimilar joining between aluminum and steel. …”
Get full text
Get full text

Underwater friction stir welding of Al-Mg alloy: Thermo-mechanical modeling and validation by Talebizadehsardari, Pouyan

“…To better understand the effects of the water environment, the results were compared with conventional friction stir welding (FSW) conditions. Thermal profile and surface heat flux results revealed that lower preheated area (PHA) at the leading edge (LE) decreased the total amount of frictional heat generation in the UFSWed joint. …”
Get full text
Get full text

Study on the effects of tool tile angle, offset and plunge depth on friction stir welding of poly(methyl methacrylate) T-joint by Eyvazian, Arameh

“…These holes and degradation of poly(methyl methacrylate) during friction stir welding process decrease strength and hardness of the joint. - IMechE 2019.…”
Get full text
Get full text

Microstructure, wear and corrosion characteristics of Cu matrix reinforced SiC–graphite hybrid composites by Jamwal A.

“…Hardness was found to decrease with the addition of graphite due to its soft nature. …”
Get full text
Get full text

Optimum design of n continuous stirred-tank bioreactors in series for fermentation processes based on simultaneous substrate and product inhibition by Abu Reesh, I.M.

Get full text
Get full text
Get full text

Hyperhydration-induced decrease in urinary luteinizing hormone concentrations of Male athletes in doping control analysis by Athanasiadou, Ioanna

“…Baseline urinary LH concentrations, expressed as the mean � SD for each individual, were within the acceptable physiological range (7.11 � 5.42 IU/L). …”
Get full text
Get full text

Synthesis and characterization of stir casted Cu-ZrO2-Graphite hybrid metal matrix composites for thermal management structures by Mittal, Prateek

“…The MMCs were prepared using stir casting technique. The composite material was developed for its application in thermal management structures. …”
Get full text
Get full text
Get full text

Phase, microstructure and tensile strength of Al–Al2O3–C hybrid metal matrix composites by Ahamad, N.

“…Hardness decreases due to variation of carbon since it has soft nature. …”
Get full text
Get full text

Structural and mechanical characterization of stir cast Al–Al2O3–TiO2 hybrid metal matrix composites by Ahamad, N.

“…Hardness decreases due to the amalgamation of reinforcements. …”
Get full text
Get full text

The Formation of Sulfide Scales on Carbon Steel in Saturated H2S by Al-Qahtani, Noora

“…There are three contributing elements of corrosion of Carbon Steel in H2S environment: the effect of H2S on water chemistry; electrochemical reactions of the bare iron surface (both anodic and cathodic processes); and the formation and growth of corrosion product layers. …”
Get full text
Get full text

The Formation of Sulfide Scales on Carbon Steel in Saturated H2S by Alqahtani, Noora

“…"There are three contributing elements of corrosion of Carbon Steel in H?S environment: the effect of H2S on water chemistry; electrochemical reactions of the bare iron surface (both anodic and cathodic processes); and the formation and growth of corrosion product layers. …”
Get full text
Get full text

Electrochemical behavior of mild and corrosion resistant concrete reinforcing steels by Sohail, Muazzam G.

“…Extensive analysis of the results indicates that the corrosion resistance of the evaluated steels was in the following decreasing order: EC, HC, MS, and HS.…”
Get full text
Get full text

Correlation of structural and mechanical properties for Al-Al2O3-SiC hybrid metal matrix composites by Ahamad, Naseem

“…Al-Al2O3-SiC hybrid composite has been developed through stir casting with addition of ceramics i.e. Al2O3-SiC (2.5 wt.%, 5.0 wt.%, 7.5 wt.% and 10.0 wt.%) in relative and symmetrical proportion. …”
Get full text
Get full text

Multifunctional self-healing polymeric nanocomposite coatings for corrosion inhibition of steel by Bahgat, Ahmed

“…The electrochemical studies indicate that the corrosion rate of the steel samples coated with the epoxy modified with the healing additives decreases after 5 days of immersion in saline water.…”
Get full text
Get full text

Multifunctional self-healing polymeric nanocomposite coatings for corrosion inhibition of steel by Ubaid F.

“…The electrochemical studies indicate that the corrosion rate of the steel samples coated with the epoxy modified with the healing additives decreases after 5 days of immersion in saline water.…”
Get full text
Get full text

Development And Performance Evaluation Of Smart Polymeric Coatings For Corrosion Protection Of Steel by Khan, Adnan

“…Consequently, they are a promising solution for longer durability of coated piping steel and decreased operation expense. If properly designed, smart self-healing coatings also help to reduce the overall thickness of the coating scheme as well as the investment cost. …”
Get full text

Understanding the Scales Formation Inhibition Mechanism on C-Steel in a Sour Media by Al-Qahtani, Noora

“…The outcome has shown that the corrosion rate of C-steel initially decreased and then stabilised with time in the CI solution that might be linked to the inhibition effect of the corrosion product layers on the iron surface. …”
Get full text
Get full text

Microstructural, tribological and compression behaviour of Copper matrix reinforced with Graphite-SiC hybrid composites by Jamwal, A.

“…Compressive strength of composites is tested using Universal testing machine and showed a decrease in value with increase in graphite content. …”
Get full text
Get full text

Mechanical characteristics of ultra-high performance steel FRC made with recycled concrete aggregates by Alnahhal, W.

“…However, the flowability was decreased by 12% to 15% with steel fibers. The results also revealed that at a steel fiber volume fraction of 0%, RCA had little influence on the compressive strength, while they noticeably influenced the flexural tensile strength. …”
Get full text
Get full text

Corrosion behavior of API X100 steel material in a hydrogen sulfide environment by Okonkwo, Paul C.

“…The results indicate that the corrosion rate of API X100 steel decreases with increasing H2S bubbling time due to the increase in H2S concentration in 3.5% NaCl solutions. …”
Get full text
Get full text