-
1
-
2
Ferroelectric Properties and Electrocaloric Effect in Dy2O3 Substitution on Lead-Free (Na0.5 Bi0.5)0.94 Ba0.06TiO3 Ceramic
Published 2023“…Higher stability of the ferroelectric (FE) phase was obtained at room temperature for the compositions y = 0.01, 0.02 and 0.05, with optimum values for y = 0.02 as remanent polarization Pr = 32µC/cm2, as well as piezoelectric coefficients d33 = 137 pC/N, kp = 0.27 and kt = 0.16, whereas a higher content of Dy (y = 0.08) induced a remarkable decrease of the ferroelectric and piezoelectric properties. …”
Get full text
-
3
Simulation and experimental study of underwater dissimilar friction-stir welding between aluminium and steel
Published 2020“…Thethickness of the IMC layer varied depending on the processing parameters with the lowestvalue of ?0.2-m. The formation of a curved interface due to enhanced materials mixing atthe advancing side is noted with a linear hardness gradient across the dissimilar weldment.Superior mechanical strength of ?…”
Get full text
Get full text
-
4
-
5
-
6
Study on the effects of tool tile angle, offset and plunge depth on friction stir welding of poly(methyl methacrylate) T-joint
Published 2019“…The best material flow and adequate heat are generated at 0 mm TA, 2� TTA and 0.2 mm TPD, respectively. The highest flexural and tensile strength of friction stir welded joint were approximately 93% and 90% of as-received poly(methyl methacrylate), respectively. …”
Get full text
Get full text
-
7
Microstructure, wear and corrosion characteristics of Cu matrix reinforced SiC–graphite hybrid composites
Published 2019“…Copper matrix composites with SiC-graphite reinforcement (0, 2.5,5, 7.5 and 10 wt.%) were prepared by stir casting process. …”
Get full text
Get full text
-
8
-
9
-
10
-
11
Synthesis and characterization of stir casted Cu-ZrO2-Graphite hybrid metal matrix composites for thermal management structures
Published 2022“…ZrO2 and Graphite reinforcements were added (0.5–0.5, 1.0–1.0, 1.5–1.5 and 2.0–2.0 wt %) in the four composite samples prepared via stir casting. …”
Get full text
Get full text
Get full text
-
12
Structural and mechanical characterization of stir cast Al–Al2O3–TiO2 hybrid metal matrix composites
Published 2020“…titanium oxide (2.5, 5.0, 7.5 and 10 wt.%) in equal proportion were prepared by stir casting. …”
Get full text
Get full text
-
13
Phase, microstructure and tensile strength of Al–Al2O3–C hybrid metal matrix composites
Published 2020“…Aluminium matrix reinforced with Al2O3–carbon (2.5, 5, 7.5 and 10 wt.%) in equal proportion was prepared by stir casting. …”
Get full text
Get full text
-
14
-
15
Structural and magnetic properties of Ni1-xZnxFe 2O4 (x=0, 0.5 and 1) nanopowders prepared by sol-gel method
Published 2013“…A series of nanostructured Ni-Zn ferrites Ni1-xZn xFe2O4 (x=0, 0.5 and 1) with a grain size from 24 to 65 nm have been prepared with a sol-gel method. …”
Get full text
Get full text
-
16
Correlation of structural and mechanical properties for Al-Al2O3-SiC hybrid metal matrix composites
Published 2021“…Al-Al2O3-SiC hybrid composite has been developed through stir casting with addition of ceramics i.e. Al2O3-SiC (2.5 wt.%, 5.0 wt.%, 7.5 wt.% and 10.0 wt.%) in relative and symmetrical proportion. …”
Get full text
Get full text
-
17
-
18
-
19
Effect of plastic deformation on Corrosion of cadmium in 0.1 m sodium Sulphate solution
Published 1993“…The results obtained indicate that the cathodic corrosion rate decreases with deformation up to 30-60% RH, depending on the surface finish. …”
Get full text
-
20
