-
1
-
2
Structural and mechanical characterization of stir cast Al–Al2O3–TiO2 hybrid metal matrix composites
Published 2020“…Aluminium matrix reinforced with aluminium oxide?titanium oxide (2.5, 5.0, 7.5 and 10 wt.%) in equal proportion were prepared by stir casting. …”
Get full text
Get full text
-
3
Biodegradable polysaccharide grafted polyacrylamide inhibitor for corrosion in CO2- saturated saline solution
Published 2023“…Electrochemical tests of Tafel and AC impedance, were used to determine the corrosion rate of carbon steel (C-steel) and protection efficiency in CO2-saturated 3.5 wt% NaCl solution. The surface morphology was characterized using FESEM coupled with EDX. …”
Get full text
Get full text
-
4
-
5
Synthesis and characterisation of Co2+-incorporated ZnO nanoparticles prepared through a sol-gel method
Published 2016“…The band gap of the Co2+-doped ZnO samples decreased from 3.19 to 2.66 eV as the content of dopant Co2+ increased from 0.0 to 1.0 wt.%. …”
Get full text
Get full text
-
6
Correlation of structural and mechanical properties for Al-Al2O3-SiC hybrid metal matrix composites
Published 2021“…Al2O3-SiC (2.5 wt.%, 5.0 wt.%, 7.5 wt.% and 10.0 wt.%) in relative and symmetrical proportion. …”
Get full text
Get full text
-
7
-
8
Thermally conductive polyethylene/expanded graphite composites as heat transfer surface: Mechanical, thermo-physical and surface behavior
Published 2020“…Moreover, the surface wettability of the HDPE/EG composite was enhanced by corona and RF plasma treatment as demonstrated by the increase in surface free energy from 28.5 mJ/m2 for untreated HDPE/EG to 55.5 and 54.5 mJ/m2 for HDPE/EG treated by corona and RF plasma, respectively. …”
Get full text
Get full text
-
9
-
10
Improved mechanical properties of recycled linear low-density polyethylene composites filled with date palm wood powder
Published 2014“…The presence of filler increased the flexural strength from 11.4MPa for unmodified RLLDPE to 17MPa for the composite containing 70wt.% filler. The Young’s modulus and stress at break measured at 50°C decreased significantly compared with those values measured at 25°C. …”
Get full text
Get full text
Get full text
-
11
-
12
Propagation rate coefficient for sulfobetaine monomers by PLP-SEC
Published 2016“…The kp values are determined in aqueous solutions for monomer concentrations between 5 and 50 wt % and temperatures between 15 and 80 °C. …”
Get full text
Get full text
-
13
-
14
Enhancing the corrosion resistance of reinforcing steel under aggressive operational conditions using behentrimonium chloride
Published 2019“…Using only a 50 ?mol L?1 of BTC, we are able to measure an inhibition efficiency of 91, 79, and 71% in SCP solution with 3.5% NaCl at pH of 12.5, 10 and 7, respectively without showing any effect on the mechanical properties on the cured mortars. …”
Get full text
Get full text
-
15
Synthesis and characterization of Sm3+-doped ZnO nanoparticles via a sol–gel method and their photocatalytic application
Published 2018“…A higher performance of samarium-doped ZnO for photocatalytic degradation of 2-chlorophenol at 0.50 wt.% was observed, compared to pure ZnO nanoparticles under the same experimental conditions.…”
Get full text
Get full text
Get full text
-
16
-
17
Mechanical Behavior of a Novel Nanocomposite Polysulphone - Carbon Nanotubes Membrane for Water Treatment
Published 2016“…m and outer diameters of 10 nm to 20 nm (corresponded aspect ratios ranging from 50 to 1000), with purity >95% and BET surface area of 156 m2/g. …”
Get full text
Get full text
