-
21
Elastic Buckling Behavior of Functionally Graded Material Thin Skew Plates with Circular Openings
Published 2024“…This study investigates the elastic buckling behavior of Functionally Graded Material (FGM) thin skew plates featuring a circular opening. FGMs, known for their unique property gradients, have gained prominence in structural engineering due to their mechanical performance and durability. …”
Get full text
article -
22
Characterization and magnetic properties of pure and transition metal doped ZnO thin films
Published 2012“…Magnetic measurements on the samples show magnetization for the as-prepared samples. The magnetization increases dramatically on vacuum annealing, which can be attributed to the incorporation of oxygen vacancy defects. …”
Get full text
Get full text
Get full text
conferenceObject -
23
Potential of horizontal louvers in increased energy savings in a commercial building in Dubai
Published 2018“…The dissertation creates a benchmark for horizontal louver configuration and its role in increasing the energy savings. This can be used as a module to recreate horizontal louvered façade on the whole building and create an impact in reducing energy expenditure of office buildings in Dubai.…”
Get full text
-
24
Comparing WZB117-liposome Synthesis via Thin-film Hydration and Microfluidic Methods
Published 2025Get full text
doctoralThesis -
25
Integration of Wind Catchers in Modern Residential Buildings in the UAE as a Means of Providing Thermal Comfort
Published 2014“…The optimal configuration when tested resulted in 47.1% decrease in degree discomfort hours and a 22.1% increase of hours annually in the thermal comfort range when compared to the existing case. …”
Get full text
-
26
Performance and microbial community variations of anaerobic digesters under increasing tetracycline concentrations
Published 2017“…Instead, a significant increase in propionic acid was observed in the reactor subjected to the highest concentration of tetracycline (20 mg/L). …”
Get full text
Get full text
Get full text
Get full text
article -
27
Effect of increasing the number of anchors on the flexural performance of FRP-strengthened RC beams
Published 2024“…This study aims to investigate the effect of increasing the number of FRP spike anchors at the laminate's ends on the flexural behavior of strengthened and anchored RC beams. …”
Get full text
article -
28
Performance of Acacia Gum as a Novel Additive in Thin Film Composite Polyamide RO Membranes
Published 2019“…<div><p>Novel thin film composite (TFC) polyamide (PA) membranes blended with 0.01–0.2 wt.% of Acacia gum (AG) have been prepared using the interfacial polymerization technique. …”
-
29
Can Ease of Doing Business Shorten the Distance and Attract Foreign Direct Investment
Published 2021“…Abstract Due to the accelerating pace of globalization, Multinational Enterprises (MNEs) have increasingly employed foreign direct investment (FDI) to enter foreign markets. …”
Get full text
-
30
Food Quality, Drug Safety, and Increasing Public Health Measures in Supply Chain Management
Published 2022“…<p dir="ltr">Over the last decade, there has been an increased interest in public health measures concerning food quality and drug safety in supply chains and logistics operations. …”
-
31
-
32
The trans-10, cis-12 isomer of conjugated linoleic acid decreases adiponectin assembly by PPARγ-dependent and PPARγ-independent mechanisms
Published 2008“…Conversely, treatment with GW9662 decreased TG mass and impaired adiponectin oligomer assembly but did not decrease total adiponectin mass. …”
Get full text
article -
33
An additive manufacturing approach based on electrohydrodynamic printing to fabricate P3HT:PCBM thin films
Published 2023“…As the annealing temperature and the flow rate were increased, discernible alterations in the PCBM clusters were consequently observed in the blends of the film and the size of the PCBM clusters has decreased by 3% while the distance between them was highly reduced by as much as 82%.…”
-
34
Friction stir extrusion of ultra-thin wall biodegradable magnesium alloy tubes — Microstructure and corrosion response
Published 2021“…For example, tubular devices such as coronary stents manufacture require defect-free, highquality tubes with thin walls (100 μm – 1 mm) as a precursor. Here, we have produced fully consolidated, structurally sound ultra-thin walled (~ 400 μm) AZ31 Mg alloy tubes by friction stir back extrusion (FSE) — a relatively new severe deformation process used typically to manufacture thick metallic tubes and rods. …”
-
35
-
36
Triple helix components supporting STEM education to increase future STEM careers in the United Arab Emirates
Published 2023“…Increasing communication between government schools, universities, and industry can benefit STEM education programs and STEM careers. …”
Get full text
-
37
Microencapsulation of phase change materials (PCMs) at low temperature using a novel thin film UV reactor
Published 2024“…In this study, a photo-induced polymerization process using a new thin film UV reactor at room temperature for PCM microencapsulation in polymer shells of different acrylate-based monomers was investigated. …”
-
38
Can AI Save Us from Burnout? Exploring Developer and QA Engineer Well-being
Published 2025“…However, several challenges have been presented by AI, including context misinterpretation, validation workload, and reducing human collaboration which can result in stress and pressure leading to burnout. …”
Get full text
Get full text
Get full text
masterThesis -
39
Can remittances alleviate energy poverty in developing countries? New evidence from panel data
Published 2023“…We demonstrate that remittances can be effectively used to alleviate energy poverty in low and middle-income countries. …”
Get full text
Get full text
Get full text
article -
40
Can remittances alleviate energy poverty in developing countries? New evidence from panel data
Published 2023“…We demonstrate that remittances can be effectively used to alleviate energy poverty in low and middle-income countries. …”
