Creep failure mode and sketch map of step-step fractured rock. by Dengke Yang (842532)

The motor torque curves of load increase/decrease (A) the load of 10 N • m (B) the load of 20 N • m. by Taochang Li (20642935)

“…<p>The motor torque curves of load increase/decrease (A) the load of 10 N • m (B) the load of 20 N • m.…”

The motor speed curves of load increase/decrease (A) the load of 10 N • m (B) the load of 20 N • m. by Taochang Li (20642935)

“…<p>The motor speed curves of load increase/decrease (A) the load of 10 N • m (B) the load of 20 N • m.…”

Knockdown of ATP2C1 results in a minor decrease of [Ca²⁺] in WPB. by Julian Terglane (12975565)

Subjects:

<b> </b> Diagram presenting the steps of process of modification and verification of the predictive equation of Work Exposure Index (WEI).... by Danuta Roman-Liu (8532645)

“…<p><b> </b> Diagram presenting the steps of process of modification and verification of the predictive equation of Work Exposure Index (WEI). …”

Extensive loading of WPB with the synthetic MaPCa Ca²⁺-Indicators affects WPB size. by Julian Terglane (12975565)

Subjects:

Creep failure mode and sketch map of slow-step fractured rock. by Dengke Yang (842532)

Increase in physical activity (100 step, 500 steps or 1000 steps) after the challenge according to decrease in screen time < or ≥60 minutes. by Annaëlle Le Steunf (19838110)

“…<p>Increase in physical activity (100 step, 500 steps or 1000 steps) after the challenge according to decrease in screen time < or ≥60 minutes.…”

Fig 9(b) in the straight-line fitting results. by Zhezhe Zhang (19704587)

“…Therefore, it can be inferred that the decrease in cohesion caused by normal unloading is the main reason for the decrease in joint instability shear strength. …”

Flow diagram illustrating the sequence of procedures executed during one time step defined as tick, each of which represents one week. by Alexandra M. Campbell (3284094)

Subjects:

Effective contact rate over time for the different modelling scenarios considered: fixed, continuously increasing, continuously decreasing and with a step-decrease. by Joshua Looker (21390948)

“…<p>Effective contact rate over time for the different modelling scenarios considered: fixed, continuously increasing, continuously decreasing and with a step-decrease.</p>…”

Error analysis. (a) Location-1 loading. (b) Location-2 loading. by Changxi Shan (22493205)

Cancer virtual patients with decreased initial neutrophil concentrations have higher viral load peaks. by Sonia T. Gazeau (21512764)

“…<b>B)</b> Sensitivity analysis determined that decreasing <i>N</i>0 (the initial concentration of neutrophils) causes higher peak viral load and peak IL-6 and IFN concentrations.…”

Relationships between total energy(a), pre-peak energy(b), post-peak energy(c) and loading rates. by Hanqiu Wang (13204812)

Disturbance of coherent behaviour leads to a decrease in information transfer. by Hannah Zoller (19688084)

Picture representing real-time visual feedback for wide step width. by Fateme Khorramroo (18086501)

Subjects:

Correlation between match load and wellness on MD+2. by Ivan Baptista (5278874)

Subjects:

Correlation between match load and wellness on MD+1. by Ivan Baptista (5278874)

Subjects:

Table of step height. by Jianbo Jia (717814)

“…Finally, by making corresponding test blocks, it was found that the peak value of forward resistance when the 10.5°test block crossed the steps of 1mm, 2mm and 3mm height decreased by 19.8%, 25.0% and 13.9% respectively, and the mean value decreased by 30.8%, 27.2% and 24.1% respectively, which was close to the simulation results, and verified the accuracy of the finite element analysis results.…”

The well wall step. by Jianbo Jia (717814)

“…Finally, by making corresponding test blocks, it was found that the peak value of forward resistance when the 10.5°test block crossed the steps of 1mm, 2mm and 3mm height decreased by 19.8%, 25.0% and 13.9% respectively, and the mean value decreased by 30.8%, 27.2% and 24.1% respectively, which was close to the simulation results, and verified the accuracy of the finite element analysis results.…”