-
141
Effect of the stretch rate during uniaxial testing on the mechanical properties of prolene
منشور في 2017"…Statistically significant findings suggest an increasing trend for Prolene® stiffness vs. stretch rate (R2 = 0.9679; two-tailed p value = 0.0025) where the stiffness increases 26.2% when increasing the displacement rate from 1 to 500 mm/min. …"
احصل على النص الكامل
احصل على النص الكامل
احصل على النص الكامل
احصل على النص الكامل
conferenceObject -
142
Harvesting water from air using adsorption material – Prototype and experimental results
منشور في 2021"…In terms of per one day (24 h), the harvester can produce 800 mL of water with an overall efficiency of 50% for 25 mm silica layer thickness. Increasing the relative humidity speeds up the adsorption cycle and increases the water capture, release and collection rates. …"
-
143
Behavioral Modeling of RF Power Amplifiers Using Reduced Sampling Rate
منشور في 2018احصل على النص الكامل
doctoralThesis -
144
-
145
-
146
Hierarchical memory synthesis in reconfigurable computers
منشور في 2002"…Because of their slow execution speed and the complexity of the problem, a novel methodology that speeds up the execution while retaining a high mapping quality is introduced. …"
احصل على النص الكامل
احصل على النص الكامل
احصل على النص الكامل
masterThesis -
147
Towards Industry 4.0 and Sustainable Manufacturing Applying Environmentally Friendly Machining of a Precipitation Hardened Stainless Steel Using Hot Turning Process
منشور في 2023"…Moreover, it has been shown that by increasing preheating temperature in hot turning, the hardness of the carbides in the workpiece decreases more than the hardness of the tool substrate and reduces coating materials, consequently reducing cutting tool abrasion wear phenomenon.…"
-
148
Digital Predistortion Using Relaxed Sampling Rates
منشور في 2022احصل على النص الكامل
doctoralThesis -
149
Simulation of the size-composition distribution of atmospheric nanoparticles over Europe
منشور في 2018"…The ground level concentrations of particles with a diameter larger than 100 nm (N100) were reproduced with a daily normalized mean error of 40 % and a daily normalized mean bias of −20 %. …"
-
150
Excess pCO2 and carbonate system geochemistry in surface seawater of the exclusive economic zone of Qatar (Arabian Gulf)
منشور في 2022"…CO2 is lost from the Gulf due to gas exchange, decreasing DIC, and reducing pCO2 to 464 μatm, similar to that observed. …"
احصل على النص الكامل
احصل على النص الكامل
احصل على النص الكامل
article -
151
-
152
"Thunderstorm distribution and frequency in Saudi Arabia"
منشور في 2005احصل على النص الكامل
article -
153
-
154
-
155
Portfolio Selection Problem Using CVaR Risk Measures Equipped with DEA, PSO, and ICA Algorithms
منشور في 2022"…It was found that when solving the Mean-CVaR model with evolutionary algorithms, the risk decreased. …"
-
156
Land surface temperature responses to land use dynamics in urban areas of Doha, Qatar
منشور في 2024"…The LST data derived from remote sensing sources demonstrates an upward trend for summer and a contrasting trend for winter. Specifically, the mean summer LST increases by 7.64 °C (0.34 °C annually), and the mean winter LST decreases by 4.87 °C (0.22 °C annually). …"
احصل على النص الكامل
احصل على النص الكامل
احصل على النص الكامل
article -
157
-
158
Tabu search based circuit optimization
منشور في 1998"…Such a strategy leads to sizable circuit speed improvement with minimum increase in the overall circuit capacitance. …"
احصل على النص الكامل
احصل على النص الكامل
article -
159
Mental health, burnout and resilience in community pharmacists during the COVID-19 pandemic: A cross-sectional study
منشور في 2022"…Participants had shown moderate resilience (mean score: 27.64 (SD = 8.31)) and their mean score fear of COVID19 was 15.67 (SD = 6.54). …"
احصل على النص الكامل
احصل على النص الكامل
احصل على النص الكامل
article -
160
Modelling the cryogenic environment aided by CFD & FEM to provide optimized solutions for unconventional manufacturing of aerospace alloys
منشور في 2020"…Cryogenic machining is steadily gaining traction as an eco-friendly unconventional machining method, effectively improving the machinability of the workpiece by cooling and lubricating the cutting process. The increased demand in the aerospace industry requires using higher cutting speeds and feeds, which adversely affect the machinability of the already difficult-tomachine aerospace alloys. …"
احصل على النص الكامل
احصل على النص الكامل
احصل على النص الكامل
masterThesis