Showing 701 - 720 results of 1,770 for search '(( 1 wt decrease ) OR ( 10 ((steel decrease) OR (((a decrease) OR (mean decrease)))) ))*', query time: 0.17s Refine Results
  1. 701

    Modified zno nanoparticles using iron ions (Fe3+) for photo-catalytic degradation of toxic pollutants under sunlight by Ba-Abbad, Muneer M.

    Published 2019
    “…As the Fe3+ concentration increased from 0.25 to 1.00 wt. %, the crystal size decreased in comparison with the undoped ZnO. …”
    Get full text
  2. 702

    Correlation of structural and mechanical properties for Al-Al2O3-SiC hybrid metal matrix composites by Ahamad, Naseem

    Published 2021
    “…Hardness of hybrid composites increases upto 5 wt.% variation of ceramic reinforcements i.e. Al2O3-SiC after that it decreases. …”
    Get full text
    Get full text
  3. 703

    CLINICAL AND ECONOMIC IMPACT OF GENETIC AND NON-GENETIC FACTORS ON INR NORMALIZATION IN PRE-OPERATIVE MANAGEMENT OF WARFARIN PATIENTS by ELJILANY, ISLAM AHMED SAYED AHMED

    Published 2021
    “…To optimize the period of preprocedural warfarin interruption to decrease the incidence of bleeding in case of bridging and the incidence of thromboembolism in case of non-bridging, a study was conducted to determine the influence of CYP2C9, VKORC1, CYP4F2, FII, and FVII genetic polymorphisms and non-genetic factors on INR decline in a cohort of Arabs undergoing a procedure that requires warfarin interruption and developing an algorithm to tailor the duration of warfarin interruption before the procedure. …”
    Get full text
  4. 704
  5. 705
  6. 706

    Deoxygenation of pyrolysis vapour derived from durian shell using catalysts prepared from industrial wastes rich in Ca, Fe, Si and Al by Tan, Y.L.

    Published 2020
    “…With same silica-to-alumina ratio, catalyst prepared from oil palm ash (AS-OPA) with lower Fe and Ca contents gave higher liquid yield (8.32 wt%) with alcohols (28.90%), hydrocarbons (46.00%), and nitrogen-containing compounds (21.46%) while catalyst prepared from electric arc furnace slag (AS-EAF) with higher Fe and Ca contents produced lower liquid yield (50.21 wt%) with high amount of esters (25.80%) and hydrocarbons (72.82%). …”
    Get full text
    Get full text
  7. 707
  8. 708

    Investigation of the rheological properties of nanosilica-reinforced polyacrylamide/polyethyleneimine gels for wellbore strengthening at high reservoir temperatures by Shamlooh M.

    Published 2019
    “…The objective of this work is to investigate the effect of nanosilica sizes (8, 20, 50, and 85 nm) and concentrations (0.1–2 wt %) on the stability and viscoelastic behavior of polyacrylamide (PAM) cross-linked with polyethyleneimine (PEI) at 130 °C. …”
    Get full text
    Get full text
  9. 709

    Fatigue and Monotonic Behaviors of Corrosion-Damaged Reinforced Concrete Beams Strengthened with FRCM Composites by Elghazy M.

    Published 2018
    “…Test results showed that the corrosion of steel bars dramatically decreased the fatigue life of the beams. …”
    Get full text
    Get full text
  10. 710
  11. 711
  12. 712

    Experimental results and modelling of corrosion-damaged concrete beams strengthened with externally-bonded composites by Elghazy M.

    Published 2018
    “…The investigated parameters included the corrosion levels (10 and 20% mass loss of steel reinforcement), the type of composite (fabric-reinforced cementitious matrix (FRCM) and fiber-reinforced polymers (FRP)), and the number of composite layers (one, two, and four). …”
    Get full text
    Get full text
  13. 713

    Structural performance and moment redistribution of basalt FRC continuous beams reinforced with basalt FRP bars by Abushanab, Abdelrahman

    Published 2021
    “…Seven beams were longitudinally reinforced with BFRP bars, while the remaining three beams were reinforced with conventional steel bars and served as a control. Test results showed that BFRC-RC beams had higher crack widths, mid-span deflections, and strains than steel-RC beams. …”
    Get full text
    Get full text
  14. 714
  15. 715
  16. 716

    Tribological studies of nanomodified mineral based multi-grade engine oil by Laad, M.

    Published 2017
    “…Tests were carried under loads of 40N, 60N and 90N at sliding speeds 0.5 m/s, 1.0 m/s and 1.5 m/s. Nanoparticle concentration in the mineral oil was taken as 1.5 wt%. …”
    Get full text
    Get full text
  17. 717

    Mobile Epifauna Associated To Artificial Substrates In Offshore Qatari Waters by Abdulaziz Aziz, Naeem

    Published 2019
    “…Thirty plates were deployed, at depths between 10 and 44 m, in each of six offshore sites, along a transect defined between natural and artificial reefs (i.e., oil platforms). …”
    Get full text
  18. 718
  19. 719
  20. 720

    Role of TiO2 and carbon nanotubes on polyethylene, and effect of accelerated weathering on photo oxidation and mechanical properties by Zagho M.M.

    Published 2019
    “…Addition of CNTs had negligible effect on the tensile strength but it kept the same approximate value of the original before the accelerated weathering (e.g., 23.2 MPa for 1 wt% of CNTs). CNTs also protected the samples even with the presence of TONPs because of the absorbance and antioxidants effects. …”
    Get full text
    Get full text