Showing 641 - 660 results of 1,761 for search '(( 10 ((steel decrease) OR (((nn decrease) OR (a decrease)))) ) OR ( 100 mean decrease ))*', query time: 0.15s Refine Results
  1. 641

    Mechanical and microstructure characterization of hard nanostructured N-bearing thin coating by Cabibbo, M.

    Published 2015
    “…The main problem with steel, is that it exhibits a relatively low hardness (below 10GPa) which strongly decreases upon annealing above about 600K. …”
    Get full text
  2. 642

    Effect of concentration of DOC loaded TiO 2 nanotubes on the corrosion behavior of smart coatings by Ubaid F.

    Published 2019
    “…Towards this direction, TiO2 nanotubes with an average size of ⁓10–15 nm (as confirmed by scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis) were synthesized through a hydrothermal process and were then impregnated with DOC. …”
    Get full text
    Get full text
  3. 643

    Experimental and numerical investigation of the flexural behavior of one-way RC slabs strengthened with near-surface mounted and externally bonded systems by Aljidda, Omar

    Published 2024
    “…In contrast, the slabs reinforced with EB experienced a decrease in ductility ranging from 38 % to 50 %. …”
    Get full text
    Get full text
  4. 644

    CLINICAL AND ECONOMIC IMPACT OF GENETIC AND NON-GENETIC FACTORS ON INR NORMALIZATION IN PRE-OPERATIVE MANAGEMENT OF WARFARIN PATIENTS by ELJILANY, ISLAM AHMED SAYED AHMED

    Published 2021
    “…To optimize the period of preprocedural warfarin interruption to decrease the incidence of bleeding in case of bridging and the incidence of thromboembolism in case of non-bridging, a study was conducted to determine the influence of CYP2C9, VKORC1, CYP4F2, FII, and FVII genetic polymorphisms and non-genetic factors on INR decline in a cohort of Arabs undergoing a procedure that requires warfarin interruption and developing an algorithm to tailor the duration of warfarin interruption before the procedure. …”
    Get full text
  5. 645
  6. 646
  7. 647

    Fatigue and Monotonic Behaviors of Corrosion-Damaged Reinforced Concrete Beams Strengthened with FRCM Composites by Elghazy M.

    Published 2018
    “…Test results showed that the corrosion of steel bars dramatically decreased the fatigue life of the beams. …”
    Get full text
    Get full text
  8. 648

    Experimental results and modelling of corrosion-damaged concrete beams strengthened with externally-bonded composites by Elghazy M.

    Published 2018
    “…The investigated parameters included the corrosion levels (10 and 20% mass loss of steel reinforcement), the type of composite (fabric-reinforced cementitious matrix (FRCM) and fiber-reinforced polymers (FRP)), and the number of composite layers (one, two, and four). …”
    Get full text
    Get full text
  9. 649

    Structural performance and moment redistribution of basalt FRC continuous beams reinforced with basalt FRP bars by Abushanab, Abdelrahman

    Published 2021
    “…Seven beams were longitudinally reinforced with BFRP bars, while the remaining three beams were reinforced with conventional steel bars and served as a control. Test results showed that BFRC-RC beams had higher crack widths, mid-span deflections, and strains than steel-RC beams. …”
    Get full text
    Get full text
  10. 650
  11. 651
  12. 652

    Mobile Epifauna Associated To Artificial Substrates In Offshore Qatari Waters by Abdulaziz Aziz, Naeem

    Published 2019
    “…Thirty plates were deployed, at depths between 10 and 44 m, in each of six offshore sites, along a transect defined between natural and artificial reefs (i.e., oil platforms). …”
    Get full text
  13. 653
  14. 654
  15. 655

    Nanocomposite Ni-TiO2 coatings produced by pulsed electroplating by Wang, Y.

    Published 2014
    “…Nanocomposite Ni-TiO2 coatings were prepared on mild steel substrate by pulse electroplating with controlled duty cycle and frequency. …”
    Get full text
    Get full text
  16. 656
  17. 657
  18. 658
  19. 659
  20. 660