Search alternatives:
11 decrease » _ decrease (Expand Search)
nn decrease » _ decrease (Expand Search)
a decrease » _ decrease (Expand Search), _ decreased (Expand Search), _ decreases (Expand Search)
10 11 » 10 12 (Expand Search)
11 decrease » _ decrease (Expand Search)
nn decrease » _ decrease (Expand Search)
a decrease » _ decrease (Expand Search), _ decreased (Expand Search), _ decreases (Expand Search)
10 11 » 10 12 (Expand Search)
-
981
Structural, wear and thermal behaviour of Cu–Al2O3–graphite hybrid metal matrix composites
Published 2020“…Copper matrix composites with Al2O3–graphite reinforcement (0.5-0.5, 1.0-1.0, 1.5-1.5 and 2.0-2.0 wt%) were prepared by stir casting process. …”
Get full text
Get full text
-
982
-
983
Synthesizing New Anodes From Qatalum's 1st Cut Spl
Published 2014“…The 1st cut SPL which is the material under study in this work is mainly composed of graphite (~ 60%), ceramic material and Al metal (~ 10%). On contrary with the 2nd Cut SPL, there is a consensus that the 1st cut SPL is a hazardous material and must be treated before dumping it in a landfill. …”
Get full text
Get full text
-
984
-
985
Changes in Copepod Community Structure in Response to Land-Based Activities along Alexandria Coastline, Mediterranean Sea
Published 2000“…Industrial discharge exerted the highest impact on the copepod population by decreasing its density to less than 500 ind./m3. Despite the decrease m copepod abundance during high flow of sewage, the impacted area sustained the maximum copepod density low discharge i.e. 11,222 ind.…”
Get full text
-
986
Effect of anions on the structural, morphological and dielectric properties of hydrothermally synthesized hydroxyapatite nanoparticles
Published 2020“…For the particles obtained from nitrate, acetate, chloride and egg shell precursors respectively give dielectric constant (εʹ) values of 9.96, 13.22, 9.92 and 10.86 at 5 MHz. The εʹ and dielectric loss (εʹʹ) values for the HA nanoparticles decrease with increase in the applied frequency as well. …”
Get full text
Get full text
-
987
-
988
-
989
-
990
-
991
-
992
The mechanical and adhesive properties of electrically and thermally conductive polymeric composites based on high density polyethylene filled with nickel powder
Published 2013“…The stress at break of the composites behaved nonlinearly; the low filler content suppressed necking, resulting in a decrease in stress at break, whereas higher filler content (higher than 10vol.%) led to reinforcement of the composites and therefore increased the stress at break.The presence of nickel particles throughout the HDPE matrix increased the hydrophilicity of the composites. …”
Get full text
Get full text
Get full text
-
993
-
994
-
995
-
996
Bond durability of sand coated and ribbed basalt FRP bars embedded in high-strength concrete
Published 2023“…However, specimens with high-strength concrete achieved most of or above their maximum bond strength after the descending stage, while those with normal-strength concrete showed a decrease in bond strength to an approximately constant value with continuous slip. …”
Get full text
Get full text
-
997
-
998
Battery-Induced Load Hiding and Its Utility Consequences
Published 2024“…Our findings reveal that the inclusion of battery users in datasets can diminish the quality of conclusions drawn from these data. This can result in a decrease in the Area Under the Curve (AUC) by more than 10% when attempting to profile users within single-occupant and multiple-occupant households. …”
Get full text
Get full text
-
999
-
1000
Application of magnetic nanoparticles for the removal of oil from oil-in-water emulsion: Regeneration/reuse of spent particles
Published 2021“…Up to 98.6% of the %Roil was attained for Coil in the range from 0 to 800 mg/L using only a DMNP of 10 mg/L. A lower DMNP of 5 mg/L recovered up to 55.6% of the oil, while increasing the DMNP > 50 mg/L did not significantly affect the %ηdem nor the %Roil. …”
Get full text
Get full text