Structural, wear and thermal behaviour of Cu–Al2O3–graphite hybrid metal matrix composites by Mittal, P.

“…Copper matrix composites with Al2O3–graphite reinforcement (0.5-0.5, 1.0-1.0, 1.5-1.5 and 2.0-2.0 wt%) were prepared by stir casting process. …”
Get full text
Get full text

Synthesis and characterisation of Co2+-incorporated ZnO nanoparticles prepared through a sol-gel method by Ba-Abbad, Muneer M.

“…The band gap of the Co2+-doped ZnO samples decreased from 3.19 to 2.66 eV as the content of dopant Co2+ increased from 0.0 to 1.0 wt.%. …”
Get full text
Get full text

Synthesis and characterization of stir casted Cu-ZrO2-Graphite hybrid metal matrix composites for thermal management structures by Mittal, Prateek

“…ZrO2 and Graphite reinforcements were added (0.5–0.5, 1.0–1.0, 1.5–1.5 and 2.0–2.0 wt %) in the four composite samples prepared via stir casting. …”
Get full text
Get full text
Get full text

Enhanced quality factor of polyvinyl formal (PVF) based nanocomposites filled with zinc oxide and carbon black nanoparticles for wireless sensing applications by Mohanapriya, M.K.

“…With further increase in CBNP content, the Q – factor was found to decrease7.38. Impedance values of PVA/ZnO/CBNP nanocomposites varied at different filler loading in PVF at 3% of CBNP (3.54 X 107Ω) to 10% of CB (1.48 X 107Ω). …”
Get full text
Get full text

Experimental and theoretical studies on the mechanical and structural changes imposed by the variation of clay loading on poly(vinyl alcohol)/cloisite 93A nanocomposites by Kabalan L.

Get full text
Get full text

Morphology, nucleation, and isothermal crystallization kinetics of poly(butylene succinate) mixed with a polycarbonate/MWCNTs masterbatch by Gumede, Thandi P.

“…The nanocomposites contained 0.5, 1.0, 2.0, and 4.0 wt% MWCNTs. Differential scanning calorimetry (DSC), small angle X-ray scattering (SAXS) and wide angle X-ray scattering (WAXS) results indicate that the blends are partially miscible, hence they form two phases (i.e., PC-rich and PBS-rich phases). …”
Get full text
Get full text

Morphology, Nucleation, and Isothermal Crystallization Kinetics of Poly(ε-caprolactone) Mixed with a Polycarbonate/MWCNTs Masterbatch by Gumede, Thandi P.

“…The nanocomposites contained 0.5, 1.0, 2.0, and 4.0 wt % MWCNTs. Even though PCL and PC have been reported to be miscible, our DSC (Differential Scanning Calorimetry), SAXS (Small Angle X-ray Scattering), and WAXS (Wide Angle X-ray Scattering) results showed partial miscibility, where two phases were formed (PC-rich and PCL-rich phases). …”
Get full text
Get full text

Synthesis and properties of HA/ZnO/CNT nanocomposite by Ding M.

“…The goal of this study was to examine the tribomechanical properties of hydroxyapatite (HA)/ZnO and HA/ZnO/CNT composite ceramics (carbon nanotubes; with different ratios 0.5 wt%, 1.0 wt%, and 1.5 wt%). The composites were synthesized using the hydrothermal method in an autoclave. …”
Get full text
Get full text

Application of Green Polymeric Nanocomposites for Enhanced Oil Recovery by Spontaneous Imbibition from Carbonate Reservoirs by Ahmadi, Yaser

“…It was found that both ENC and WNC nanocomposites decreased CA and IFT, but ENC performed better than WNC under different salinities, namely, seawater (SW), double diluted salted (2 SW), ten times diluted seawater (10 SW), formation water (FW), and distilled water (DIW), which were applied at 70 °C, 2000 psi, and 0.05 wt.% nanocomposites concentration. …”
Get full text
Get full text
Get full text

Fabrication of Fouling Resistant Ti3C2Tx(MXene) Cellulose Acetate Nanocomposite Membrane for Forward Osmosis Application by Alfahel, Radwan Ahmad Firas

“…It was observed that the cross-linked cellulose acetate membrane with 8 wt% MXene (CCAM-8%) showed higher resistance to fouling when compared with commercial thin-filmcomposite (TFC) FO membrane, the water flux of CCAM-8% decreased by only 10.7% using TSE as FS compared to DI, where the water flux of the TFC commercial membrane decreased by 32.2% when using TSE as FS compared to DI.…”
Get full text

Phase, microstructure and tensile strength of Al–Al2O3–C hybrid metal matrix composites by Ahamad, N.

“…Aluminium matrix reinforced with Al2O3–carbon (2.5, 5, 7.5 and 10 wt.%) in equal proportion was prepared by stir casting. …”
Get full text
Get full text

Structural and mechanical characterization of stir cast Al–Al2O3–TiO2 hybrid metal matrix composites by Ahamad, N.

“…titanium oxide (2.5, 5.0, 7.5 and 10 wt.%) in equal proportion were prepared by stir casting. …”
Get full text
Get full text

Combined effects of treated domestic wastewater, fly ash, and calcium nitrite toward concrete sustainability by Abushanab, Abdelrahman

Get full text
Get full text

Improved flexible, controlled dielectric constant material from recycled LDPE polymer composites by Noorunnisa Khanam, P.

Get full text
Get full text
Get full text

Modified zno nanoparticles using iron ions (Fe3+) for photo-catalytic degradation of toxic pollutants under sunlight by Ba-Abbad, Muneer M.

Get full text

Effect of electroless bath composition on the mechanical, chemical, and electrochemical properties of new NiP-C 3 N 4 nanocomposite coatings by Fayyad E.M.

Get full text
Get full text

Plasticization and co-crystallization in LLDPE/wax blends. by Gumede, Thandi P.

Get full text
Get full text

Enhancing the corrosion resistance of reinforcing steel under aggressive operational conditions using behentrimonium chloride by Radwan A.B.

“…Using only a 50 ?mol L?1 of BTC, we are able to measure an inhibition efficiency of 91, 79, and 71% in SCP solution with 3.5% NaCl at pH of 12.5, 10 and 7, respectively without showing any effect on the mechanical properties on the cured mortars. …”
Get full text
Get full text

Effect of surfactants on the convective heat transfer and pressure drop characteristics of ZnO/DIW nanofluids: An experimental study by Qamar, Adnan

Get full text
Get full text
Get full text