-
1
-
2
-
3
-
4
-
5
Structural, wear and thermal behaviour of Cu–Al2O3–graphite hybrid metal matrix composites
Published 2020“…Copper matrix composites with Al2O3–graphite reinforcement (0.5-0.5, 1.0-1.0, 1.5-1.5 and 2.0-2.0 wt%) were prepared by stir casting process. …”
Get full text
Get full text
-
6
Synthesis and characterization of stir casted Cu-ZrO2-Graphite hybrid metal matrix composites for thermal management structures
Published 2022“…ZrO2 and Graphite reinforcements were added (0.5–0.5, 1.0–1.0, 1.5–1.5 and 2.0–2.0 wt %) in the four composite samples prepared via stir casting. …”
Get full text
Get full text
Get full text
-
7
Influence of nitrogen doping on the electrocatalytic activity of Ni-incorporated carbon nanofibers toward urea oxidation
Published 2017“…However, the electrochemical measurements indicated that the content of the urea in the initial electrospun solution should be optimized as the results showed that the best nickel surface activation as well as the maximum observed current density can be achieved when the urea content is kept at 5 wt%. Typically, the observed current densities using 1.0 M urea (in 1 M KOH) were 3.15, 29.7, 13.75, 47.55, 14.13 and 9.85 mA/cm2 for the nanofibers obtained from electrospun solutions having 0, 1, 2, 5, 7 and 9 wt% urea, respectively. …”
Get full text
Get full text
-
8
-
9
Synthesis and characterisation of Co2+-incorporated ZnO nanoparticles prepared through a sol-gel method
Published 2016“…The band gap of the Co2+-doped ZnO samples decreased from 3.19 to 2.66 eV as the content of dopant Co2+ increased from 0.0 to 1.0 wt.%. …”
Get full text
Get full text
-
10
Enhanced quality factor of polyvinyl formal (PVF) based nanocomposites filled with zinc oxide and carbon black nanoparticles for wireless sensing applications
Published 2019“…The incorporation of ZnO at 10% decreases Q-factor to 36.1. Incorporation of CBNP at 5% and ZnO at 5% further reduces the Q-factor to 13.7. …”
Get full text
Get full text
-
11
Effect of concentration of DOC loaded TiO 2 nanotubes on the corrosion behavior of smart coatings
Published 2019“…Various contents of the encapsulated TiO2 nanotubes (1, 3 and 5 wt%) were thoroughly dispersed into the epoxy matrix and the resulting composites were then applied on a cleaned steel substrate using doctor blade technique to develop smart coatings. …”
Get full text
Get full text
-
12
-
13
Correlation of structural and mechanical properties for Al-Al2O3-SiC hybrid metal matrix composites
Published 2021“…Al-Al2O3-SiC hybrid composite has been developed through stir casting with addition of ceramics i.e. Al2O3-SiC (2.5 wt.%, 5.0 wt.%, 7.5 wt.% and 10.0 wt.%) in relative and symmetrical proportion. …”
Get full text
Get full text
-
14
Morphology, nucleation, and isothermal crystallization kinetics of poly(butylene succinate) mixed with a polycarbonate/MWCNTs masterbatch
Published 2018“…The nanocomposites contained 0.5, 1.0, 2.0, and 4.0 wt% MWCNTs. Differential scanning calorimetry (DSC), small angle X-ray scattering (SAXS) and wide angle X-ray scattering (WAXS) results indicate that the blends are partially miscible, hence they form two phases (i.e., PC-rich and PBS-rich phases). …”
Get full text
Get full text
-
15
Morphology, Nucleation, and Isothermal Crystallization Kinetics of Poly(ε-caprolactone) Mixed with a Polycarbonate/MWCNTs Masterbatch
Published 2017“…The nanocomposites contained 0.5, 1.0, 2.0, and 4.0 wt % MWCNTs. Even though PCL and PC have been reported to be miscible, our DSC (Differential Scanning Calorimetry), SAXS (Small Angle X-ray Scattering), and WAXS (Wide Angle X-ray Scattering) results showed partial miscibility, where two phases were formed (PC-rich and PCL-rich phases). …”
Get full text
Get full text
-
16
Conversion of Organic Municipal Wastes into Biochars and their Effect on Fertility Parameters of Normal and Sabkha Soils of Qatar
Published 2016“…To each pot, sufficient amount of 0.25-mm sieved biochar was mixed with soil to yield carbon to soil ratios of 0, 1, and 2% (wt/wt). Box-Behnken experimental design was used instead of the full factorial to decrease the number of treatments to a manageable level (126 treatments) with three replications at the center. …”
Get full text
Get full text
-
17
Phase, microstructure and tensile strength of Al–Al2O3–C hybrid metal matrix composites
Published 2020“…Aluminium matrix reinforced with Al2O3–carbon (2.5, 5, 7.5 and 10 wt.%) in equal proportion was prepared by stir casting. …”
Get full text
Get full text
-
18
Structural and mechanical characterization of stir cast Al–Al2O3–TiO2 hybrid metal matrix composites
Published 2020“…Aluminium matrix reinforced with aluminium oxide?titanium oxide (2.5, 5.0, 7.5 and 10 wt.%) in equal proportion were prepared by stir casting. …”
Get full text
Get full text
-
19
-
20
