Structural, wear and thermal behaviour of Cu–Al2O3–graphite hybrid metal matrix composites by Mittal, P.

“…The aim of the present study is to investigate the structural, wear and thermal behaviour of Cu–Al2O3–graphite hybrid metal matrix composites. Copper matrix composites with Al2O3–graphite reinforcement (0.5-0.5, 1.0-1.0, 1.5-1.5 and 2.0-2.0 wt%) were prepared by stir casting process. …”
Get full text
Get full text

Synthesis and characterisation of Co2+-incorporated ZnO nanoparticles prepared through a sol-gel method by Ba-Abbad, Muneer M.

“…The band gap of the Co2+-doped ZnO samples decreased from 3.19 to 2.66 eV as the content of dopant Co2+ increased from 0.0 to 1.0 wt.%. …”
Get full text
Get full text

Structural and mechanical characterization of stir cast Al–Al2O3–TiO2 hybrid metal matrix composites by Ahamad, N.

“…Aluminium matrix reinforced with aluminium oxide?titanium oxide (2.5, 5.0, 7.5 and 10 wt.%) in equal proportion were prepared by stir casting. …”
Get full text
Get full text

Synthesis and characterization of stir casted Cu-ZrO2-Graphite hybrid metal matrix composites for thermal management structures by Mittal, Prateek

“…The properties of the prepared MMCs were found to be dependent on the reinforcements content present in the MMCs. ZrO2 and Graphite reinforcements were added (0.5–0.5, 1.0–1.0, 1.5–1.5 and 2.0–2.0 wt %) in the four composite samples prepared via stir casting. …”
Get full text
Get full text
Get full text

Phase, microstructure and tensile strength of Al–Al2O3–C hybrid metal matrix composites by Ahamad, N.

“…Aluminium matrix reinforced with Al2O3–carbon (2.5, 5, 7.5 and 10 wt.%) in equal proportion was prepared by stir casting. …”
Get full text
Get full text

Morphology, nucleation, and isothermal crystallization kinetics of poly(butylene succinate) mixed with a polycarbonate/MWCNTs masterbatch by Gumede, Thandi P.

“…The nanocomposites contained 0.5, 1.0, 2.0, and 4.0 wt% MWCNTs. Differential scanning calorimetry (DSC), small angle X-ray scattering (SAXS) and wide angle X-ray scattering (WAXS) results indicate that the blends are partially miscible, hence they form two phases (i.e., PC-rich and PBS-rich phases). …”
Get full text
Get full text

Synthesis and properties of HA/ZnO/CNT nanocomposite by Ding M.

Get full text
Get full text

Morphology, Nucleation, and Isothermal Crystallization Kinetics of Poly(ε-caprolactone) Mixed with a Polycarbonate/MWCNTs Masterbatch by Gumede, Thandi P.

“…The nanocomposites contained 0.5, 1.0, 2.0, and 4.0 wt % MWCNTs. Even though PCL and PC have been reported to be miscible, our DSC (Differential Scanning Calorimetry), SAXS (Small Angle X-ray Scattering), and WAXS (Wide Angle X-ray Scattering) results showed partial miscibility, where two phases were formed (PC-rich and PCL-rich phases). …”
Get full text
Get full text

Improved flexible, controlled dielectric constant material from recycled LDPE polymer composites by Noorunnisa Khanam, P.

Get full text
Get full text
Get full text

Modified zno nanoparticles using iron ions (Fe3+) for photo-catalytic degradation of toxic pollutants under sunlight by Ba-Abbad, Muneer M.

“…As the Fe3+ concentration increased from 0.25 to 1.00 wt. %, the crystal size decreased in comparison with the undoped ZnO. …”
Get full text

Effect of electroless bath composition on the mechanical, chemical, and electrochemical properties of new NiP-C 3 N 4 nanocomposite coatings by Fayyad E.M.

“…It has an efficiency of approximately 96% that decreased gradually, losing about only 2% after one week and 20% after one month of immersion time in the aforementioned chloride solution.…”
Get full text
Get full text

Enhancing the corrosion resistance of reinforcing steel under aggressive operational conditions using behentrimonium chloride by Radwan A.B.

“…Using only a 50 ?mol L?1 of BTC, we are able to measure an inhibition efficiency of 91, 79, and 71% in SCP solution with 3.5% NaCl at pH of 12.5, 10 and 7, respectively without showing any effect on the mechanical properties on the cured mortars. …”
Get full text
Get full text