Showing 461 - 480 results of 1,778 for search '(( 5 h decrease ) OR ( 10 (((peter OR per) decrease) OR (((a decrease) OR (mean decrease)))) ))*', query time: 0.21s Refine Results
  1. 461

    Corrosion behavior of API-X120 carbon steel alloy in a GTL F-T process water environment at low COD concentration by Ewis, Dina

    Published 2020
    “…Electrochemical impedance spectroscopy and potentiodynamic polarization techniques were used to determine the carbon steel corrosion rate under temperatures ranging from 293 to 323 K and rotation speed of 0, 500, 1000, 2000 rpm when the immersion time was 0.5, 1, and 2 h. The corrosion rate increased with temperature and rotation speed but decreased with immersion time. …”
    Get full text
    Get full text
  2. 462
  3. 463

    Improved properties of Al-Si3N4 nanocomposites fabricated through a microwave sintering and hot extrusion process by Matli, Penchal Reddy

    Published 2017
    “…In this study, nano-sized Si3N4 (0, 0.5, 1.0 and 1.5 vol%)/Al composites were fabricated using a powder metallurgy method involving microwave sintering technique followed by hot extrusion. …”
    Get full text
    Get full text
  4. 464

    An experimental study on achieving even-frosting for an air source heat pump using a novel dual-fan outdoor coil by Bai, Xiaoxia

    Published 2022
    “…Besides, as tTIAO values were decreased from 15 mins to 10 mins for both fans, and to 6 mins for Fan A and 8 mins for Fan B, heating/frosting operation duration was increased by 8.9% and 19.4%, respectively, at a higher and , as compared to those using the traditional single-fan outdoor coil. …”
    Get full text
    Get full text
  5. 465
  6. 466
  7. 467

    Numerical analysis of spatial distribution of carbon in methane dry reforming over supported nickel catalyst in a packed bed reactor by Ebrahimi, Parisa

    Published 2024
    “…The total carbon deposited was estimated to be around 18 g after 10,000 s of Time on Stream (TOS) at 650 °C. As the temperature increased, the total carbon deposition decreased, although this reduction became negligible beyond 850 °C. …”
    Get full text
    Get full text
    Get full text
    article
  8. 468
  9. 469
  10. 470

    PREVALENCE OF BREASTFEEDING INDICATORS IN MIDDLE EAST AND NORTH AFRICAN COUNTRIES: A META-ANALYSIS OF NATIONAL HEALTH SURVEYS (2010- 2020) by NASSER, AMAL ABDO

    Published 2022
    “…As cesarean section rates increased to more than 10%, the prevalence of breastfeeding indicators decreased. …”
    Get full text
  11. 471
  12. 472
  13. 473
  14. 474
  15. 475
  16. 476

    Efficacy of a novel topical fipronil, (S)-methoprene, eprinomectin and praziquantel combination against naturally acquired intestinal nematode and cestode infections in cats by Knaus, Martin

    Published 2014
    “…In each study, cats were assigned randomlyto blocks of two animals each, based on decreasing pre-treatment body weight and wererandomly allocated to one of two groups of six to 12 cats: untreated (control) or treatedwith topical fipronil (8.3%, w/v), (S)-methoprene (10%, w/v), eprinomectin (0.4%, w/v)and praziquantel (8.3%, w/v) (BROADLINE®, Merial) at 0.12 mL/kg body weight (providinga minimum of 10 mg fipronil + 12 mg S-methoprene + 0.5 mg eprinomectin + 10 mg prazi-quantel per kg body weight). …”
    Get full text
    Get full text
  17. 477
  18. 478

    Impact of aluminium acetate particles size on the gelation kinetics of polyacrylamide-based gels: Rheological and molecular simulation study by Hamza A.

    Published 2021
    “…The addition of bentonite at low crosslinker concentrations (0.5–1 wt.%) did not decrease the gel strength of 7 wt.% PAM/1 wt.% AlAc significantly. …”
    Get full text
    Get full text
    Get full text
  19. 479
  20. 480