Search alternatives:
mg decrease » _ decrease (Expand Search)
we decrease » _ decrease (Expand Search)
a decrease » _ decrease (Expand Search), _ decreased (Expand Search), _ decreases (Expand Search)
mg decrease » _ decrease (Expand Search)
we decrease » _ decrease (Expand Search)
a decrease » _ decrease (Expand Search), _ decreased (Expand Search), _ decreases (Expand Search)
-
1001
Structural, wear and thermal behaviour of Cu–Al2O3–graphite hybrid metal matrix composites
Published 2020“…Copper matrix composites with Al2O3–graphite reinforcement (0.5-0.5, 1.0-1.0, 1.5-1.5 and 2.0-2.0 wt%) were prepared by stir casting process. …”
Get full text
Get full text
-
1002
-
1003
Synthesizing New Anodes From Qatalum's 1st Cut Spl
Published 2014“…The 1st cut SPL which is the material under study in this work is mainly composed of graphite (~ 60%), ceramic material and Al metal (~ 10%). On contrary with the 2nd Cut SPL, there is a consensus that the 1st cut SPL is a hazardous material and must be treated before dumping it in a landfill. …”
Get full text
Get full text
-
1004
-
1005
Effect of anions on the structural, morphological and dielectric properties of hydrothermally synthesized hydroxyapatite nanoparticles
Published 2020“…For the particles obtained from nitrate, acetate, chloride and egg shell precursors respectively give dielectric constant (εʹ) values of 9.96, 13.22, 9.92 and 10.86 at 5 MHz. The εʹ and dielectric loss (εʹʹ) values for the HA nanoparticles decrease with increase in the applied frequency as well. …”
Get full text
Get full text
-
1006
-
1007
-
1008
-
1009
-
1010
-
1011
Effect of concentration of DOC loaded TiO 2 nanotubes on the corrosion behavior of smart coatings
Published 2019“…Towards this direction, TiO2 nanotubes with an average size of ⁓10–15 nm (as confirmed by scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis) were synthesized through a hydrothermal process and were then impregnated with DOC. …”
Get full text
Get full text
-
1012
-
1013
-
1014
-
1015
-
1016
The mechanical and adhesive properties of electrically and thermally conductive polymeric composites based on high density polyethylene filled with nickel powder
Published 2013“…The stress at break of the composites behaved nonlinearly; the low filler content suppressed necking, resulting in a decrease in stress at break, whereas higher filler content (higher than 10vol.%) led to reinforcement of the composites and therefore increased the stress at break.The presence of nickel particles throughout the HDPE matrix increased the hydrophilicity of the composites. …”
Get full text
Get full text
Get full text
-
1017
-
1018
Bond durability of sand coated and ribbed basalt FRP bars embedded in high-strength concrete
Published 2023“…However, specimens with high-strength concrete achieved most of or above their maximum bond strength after the descending stage, while those with normal-strength concrete showed a decrease in bond strength to an approximately constant value with continuous slip. …”
Get full text
Get full text
-
1019
Production and investigation of flexible nanofibers of sPEEK/PVP loaded with RuO2 nanoparticles
Published 2021“…The samples were synthesized with different concentrations of hydrous ruthenium chloride of 2 wt%, 5 wt%, and 10 wt%, and then annealed at a temperature of 300 �C for 4 h to form the ruthenium oxide nanoparticles. …”
Get full text
Get full text
-
1020