Search alternatives:
largest decrease » largest decreases (Expand Search), marked decrease (Expand Search)
linear decrease » linear increase (Expand Search)
larger decrease » marked decrease (Expand Search)
laser decrease » water decreases (Expand Search), teer decrease (Expand Search), asdr decreased (Expand Search)
largest decrease » largest decreases (Expand Search), marked decrease (Expand Search)
linear decrease » linear increase (Expand Search)
larger decrease » marked decrease (Expand Search)
laser decrease » water decreases (Expand Search), teer decrease (Expand Search), asdr decreased (Expand Search)
-
121
Concept of heat-dissipation time as a fundamental constraint to the realised travel speeds of animals.
Published 2023“…(<b>b</b>) A greater supply of metabolic power combined with a higher locomotion efficiency allows larger animals to sustain higher potential travel speeds. …”
-
122
-
123
-
124
Scheme of g-λ model with larger values λ.
Published 2024“…The stress-deformation model of the single uncoupled joint (g-λ model with λ ≥ 1) is employed to depict the nonlinearity of uncoupled joints, with a greater value of the parameter λ signifying a lower degree of non-linearity in the joint model curve. …”
-
125
Reversely Exploring Higher-Order Effects in a Fiber Laser through Physics-Informed Recursive Neural Network
Published 2024“…In ultrafast fiber lasers, the influence of higher-order effects on mode-locked pulses becomes increasingly notable as the pulse width decreases from the subpicosecond to the femtosecond level. …”
-
126
KAIST low-speed wind tunnel and its components.
Published 2024“…Experimental results regarding the decrease of the laser intensity via scattering confirmed that the theoretical and experimental values resulted in a similar decrease rate under static conditions. …”
-
127
Scattering efficiency by particle diameter.
Published 2024“…Experimental results regarding the decrease of the laser intensity via scattering confirmed that the theoretical and experimental values resulted in a similar decrease rate under static conditions. …”
-
128
Relative transmission rate by wavelength.
Published 2024“…Experimental results regarding the decrease of the laser intensity via scattering confirmed that the theoretical and experimental values resulted in a similar decrease rate under static conditions. …”
-
129
-
130
-
131
The introduction of mutualisms into assembled communities increases their connectance and complexity while decreasing their richness.
Published 2025“…Parameter values: interaction strengths were drawn from a half-normal distribution of zero mean and a standard deviation of 0.2, and strength for consumers was made no larger than the strength for resources. …”
-
132
-
133
-
134
Data_Sheet_1_Artificial Wetlands as Breeding Habitats for Shorebirds: A Case Study on Pied Avocets in China’s Largest Saltpan Complex.docx
Published 2021“…The DSR decreased over the course of the 71-days nesting season and followed a linear trend. …”
-
135
Laser-Assisted Structures for Efficient Fluid Management on Stainless Steel Surfaces
Published 2024“…The article presents a high-productivity laser-structuring method combined with a hydrophobic post-treatment to create zone-structured surfaces with a decreasing wetting angle on AISI 304 stainless steel surfaces. …”
-
136
Results of Multiple Linear Regression.
Published 2025“…We then used multiple linear regressions to examine spatiotemporal mechanisms underlying gait speed changes across terrains. …”
-
137
Multiple linear regression models.
Published 2023“…Serum renin and urinary EGF levels were determined with a commercial ELISA kit. Partial Spearman rank correlation coefficients and multiple linear regression models were used to study the association between renin, the urinary EGF/urinary creatinine ratio and blood pressure parameters. …”
-
138
-
139
3D-Printed Diamond–Titanium Composite: A Hybrid Material for Implant Engineering
Published 2019“…Up until now, diamond implants have been fabricated using coating technologies or embedding diamond nanoparticles in polymer matrices. Here we demonstrated a method of manufacturing diamond implants using laser cladding technology to 3D print a composite of diamond and fused titanium material. …”
-
140
Solid Cure of Poly(phenylene sulfide): Competition between Increasing Nucleation Density and Decreasing Growth Rate
Published 2024“…Commercial cured poly(phenylene sulfide) (PPS) is produced by the thermal oxidation treatment of linear PPS in the solid state. Branching and oxidation reactions occur, and correspondingly, the crystallization behaviors of PPS change a lot. …”