Ultrasmooth Micromilling of Stainless Steel by Ultrashort Pulsed Laser Ablation Using MHz Bursts by Xiao Jia (1703719)

“…To fill this research gap, the present study conducts a comprehensive investigation on the surface processing of stainless steel using ultrashort pulsed laser burst ablation. …”

Increase in physical activity (100 step, 500 steps or 1000 steps) after the challenge according to decrease in screen time < or ≥60 minutes. by Annaëlle Le Steunf (19838110)

“…<p>Increase in physical activity (100 step, 500 steps or 1000 steps) after the challenge according to decrease in screen time < or ≥60 minutes.…”

Flow diagram illustrating the sequence of procedures executed during one time step defined as tick, each of which represents one week. by Alexandra M. Campbell (3284094)

Subjects:

Polarization curve of galvanized steel. by Shan Lin (228596)

Subjects:

Process of steel truss incremental launching. by Zhe Hu (787283)

“…However, prediction accuracy diminishes for longer time steps as the step length increases. Following model updates with measured data, the accumulated prediction error rapidly decreases. …”

Effective contact rate over time for the different modelling scenarios considered: fixed, continuously increasing, continuously decreasing and with a step-decrease. by Joshua Looker (21390948)

“…<p>Effective contact rate over time for the different modelling scenarios considered: fixed, continuously increasing, continuously decreasing and with a step-decrease.</p>…”

Actual statistical data of steel enterprises. by Junwen Chen (4862806)

Subjects:

Scope and boundary of iron and steel system. by Junwen Chen (4862806)

Subjects:

Residual stresses versus steel strength. by Yihan Tu (22258445)

Subjects:

SEM morphology of power: (a)17−4PH; (b)TiC. by Dian Yu Luo (22656111)

Subjects:

Electrochemical impedance spectroscopy of galvanized steel. by Shan Lin (228596)

Subjects:

(a) The installation method of blade holder, (b) Blades in operation, (c) The blade after 120h of wheat harvesting. by Dian Yu Luo (22656111)

Subjects:

DataSheet1_Study on the effects of laser shock peening on the microstructure and properties of 17-7PH stainless steel.docx by Kangwen Li (19921167)

“…<p>To investigate the surface integrity of 17-7PH stainless steel welded structural components used in aviation, laser shock peening (LSP) with different power densities was applied to stainless steel welded joints. …”

HSF2 reduced the decrease in the MMP in Caco-2 cells, which were observed by laser confocal microscopy. by Wen Wang (6570)

Polarization curve of Q235 carbon steel. by Shan Lin (228596)

Subjects:

Disturbance of coherent behaviour leads to a decrease in information transfer. by Hannah Zoller (19688084)

SEM morphology and EDS surface-scanning energy spectra of 17-4PH-xTiC coated abrasion marks: (a) 10%TiC; (b) 20%TiC; (c) 30%TiC; (d) 40%TiC. by Dian Yu Luo (22656111)

Subjects:

Electrochemical impedance spectroscopy of Q235 carbon steel. by Shan Lin (228596)

Subjects:

Open circuit potential test results of galvanized steel. by Shan Lin (228596)

Subjects:

Table of step height. by Jianbo Jia (717814)

“…Finally, by making corresponding test blocks, it was found that the peak value of forward resistance when the 10.5°test block crossed the steps of 1mm, 2mm and 3mm height decreased by 19.8%, 25.0% and 13.9% respectively, and the mean value decreased by 30.8%, 27.2% and 24.1% respectively, which was close to the simulation results, and verified the accuracy of the finite element analysis results.…”