Upstream and downstream smoke level (mg/m³) and filtering efficiency (%) of DPF module under different loads. حسب Xiaobo Li (118828)

الموضوعات:

Static loading procedure. حسب Tek Raj Gyawali (20550560)

"…Panels reinforced with thinner PVA fibers exhibited superior performance in resisting compressive and impact loads. This enabled a reduction in fiber content to 1.2% (a 60% decrease) and panel thickness to 22 mm (a 4.35% decrease) compared to panels with thicker fibers. …"

The influence of Cu content on high temperature corrosion behavior of heat - resistant molten salt steel حسب Hong Li (20183)

"…The structure of the oxide film consists of various protective oxide films; with increasing of Cu content, the high-temperature corrosion resistance of heat-resistant steel was improved and the thickness of the corrosion layer was decreased which led to improving the bonding strength between the inner layer and the matrix. …"

Image_1_The Mechanism of Heat Stress Resistance During Spermatogenesis in Turpan Black Sheep.TIF حسب Yukun Song (1468750)

"…There was no significant difference in testicular histomorphology between the two after heat stress treatment. However, Suffolk sheep showed a significantly decreased number of spermatocytes after heat stress treatment (p < 0.05). …"

Image_3_The Mechanism of Heat Stress Resistance During Spermatogenesis in Turpan Black Sheep.TIF حسب Yukun Song (1468750)

"…There was no significant difference in testicular histomorphology between the two after heat stress treatment. However, Suffolk sheep showed a significantly decreased number of spermatocytes after heat stress treatment (p < 0.05). …"

Image_2_The Mechanism of Heat Stress Resistance During Spermatogenesis in Turpan Black Sheep.TIF حسب Yukun Song (1468750)

"…There was no significant difference in testicular histomorphology between the two after heat stress treatment. However, Suffolk sheep showed a significantly decreased number of spermatocytes after heat stress treatment (p < 0.05). …"

Uncropped blots corresponding to Fig 2B, provided for assessment of band specificity and loading consistency. حسب Tetsuya Kakita (4922584)

Uncropped blots corresponding to Fig 3A, provided for assessment of band specificity and loading consistency. حسب Tetsuya Kakita (4922584)

Group M and N component simulation conditions and calculation results. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Modeling assembly. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Development of stress distribution in peak stage. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Failure modes of the circular member. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Energy variety of CFRP layers and concrete for each component. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

A1, A3, A6 bending moment variation. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Shows the <i>AC</i> area and the time difference between elements C2 and C3. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

The time-history curve of the impact force of test member. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Comparison of deflection time-history curves crack and development diagram of circular members. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Comparison of peak values of maximum principal stress curves. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Test members’ deflection curve. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات:

Simulation results of group M and N components. حسب Khalil AL-Bukhaiti (16015543)

الموضوعات: