Search alternatives:
peter » peer (Expand Search)
sami » same (Expand Search), semi (Expand Search)
Showing 741 - 760 results of 813 for search '(( greater decrease ) OR ((( peter decrease ) OR ((( five decrease ) OR ( sami increase ))))))', query time: 0.14s Refine Results
  1. 741

    Synthesis of lithium manganese oxide nanocomposites using microwave‐assisted chemical precipitation technique and their performance evaluation in lithium‐ion batteries by Hanan Abdurehman Tariq (14778361)

    Published 2023
    “…The LMO-CNTs and LMO-GNPs have an excellent rate capability of 124 and 127 mAhg<sup>−1</sup> at 0.1C, sustained at 115.6 and 118.5 mAhg<sup>−1</sup> at 10C, respectively. Cycling efficiency is also improved, with LMO-CNTs and LMO-GNPs having an initial capacity of 124 and 127 mAhg<sup>−1</sup> decreasing to 112 and 114 mAhg<sup>−1</sup>, respectively, after 50 cycles. …”
  2. 742
  3. 743
  4. 744
  5. 745

    Hippocampal Programmed Cell Death after Status Epilepticus by Abi-Habib, Ralph J.

    Published 2003
    “…Ceramide, a known mediator of PCD in multiple neural and nonneural tissues, increased at 2–3 h after KA intraperitoneal injection, and then decreased to control levels before increasing again from 12 to 30 h after injection. …”
    Get full text
    Get full text
    Get full text
    article
  6. 746

    Drug Resistance Induction and Phenotypic and Genotypic Characterization of a Candida albicans Drug Sensitive Isolate by El Hachem, Setrida Charbel

    Published 2023
    “…In the ALS4 gene for example, we observed 2 mutations in the susceptible strain and 5 mutations in the resistant strain. This is the first study of its kind to induce drug resistance followed by a genotypic and phenotypic analysis of the isolates, with the aim of determining mechanisms of resistance to antifungal drugs.…”
    Get full text
    Get full text
    Get full text
    masterThesis
  7. 747

    An additive manufacturing approach based on electrohydrodynamic printing to fabricate P3HT:PCBM thin films by Zulfikre Esa (19457344)

    Published 2023
    “…The estimated film mass and thickness were found between 3.235 and 23.471 mg and 597.5 nm to 1.60 µm, respectively. The films exhibited a broad visible absorption spectrum ranging from ~ 340 to ~ 600 nm, with a maximum peak λ<sub>max</sub> located at ~ 500 nm. …”
  8. 748

    Pilot scale evaluation of thin film composite membranes for reducing wastewater volumes: osmotic concentration process by Abdelrahman M. Awad (16932519)

    Published 2023
    “…The membrane achieved a water flux of 10 LMH, which slightly decreased to 9.6 after 48 h of operation, mainly due to inorganic scaling. …”
  9. 749
  10. 750
  11. 751

    Road safety and traffic medicine in Iran: Achievements and challenges by A. Motevalian (19807242)

    Published 2015
    “…The number of annual fatalities, which had been on the rise for several decades, reached to the maximum number of over 27500 deaths in 2005. The number decreased to 23000 in 2010 and less than 18000 in 2013. …”
  12. 752

    A Multidecadal Assessment of Haze Development and Fluctuations in Visibility for Arabian Peninsula by Luqman Atique (16036586)

    Published 2024
    “…Visibility in KWT was 0.5 km in 1994, indicating a period of exceptionally poor visibility whereas the daily mean visibility for KSA was approximately 0.6 km. …”
  13. 753

    Influence of co-current vapor flow on falling film over horizontal tube by Furqan Tahir (14429547)

    Published 2021
    “…The average film thickness and wetting time is reduced by 14.1% and 18.5%, respectively for the vapor velocity of 6 m/s compared to the no vapor flow, for 0.02 kg/(m·s). …”
  14. 754

    Two-stage optimisation for malachite green removal using activated date pits by M. Hijab (14152095)

    Published 2022
    “…<p>Water pollution, from industry and agriculture, is a major threat to water security in the light of decreasing global potable water resources. Adsorption is one potential treatment technology for the removal of different contaminants from polluted water. …”
  15. 755

    Addressing Challenges of Distance Learning in the Pandemic with Edge Intelligence Enabled Multicast and Caching Solution by Kashif Bilal (16896357)

    Published 2022
    “…In the scenario of distance learning, there is ample opportunity to realize multi-cast delivery instead of a conventional unicast. However, the existing 5G architecture does not support service-less multi-cast. …”
  16. 756

    Influence of temperature on tire-pavement noise in hot climates: Qatar case by Okan Sirin (14603304)

    Published 2021
    “…This temperature correction factor is developed based on the local environment (temperature varying from 5 °C to 35 °C) and generally varies with different pavements. …”
  17. 757

    Acute intense fatigue does not modify the effect of EVA and TPU custom foot orthoses on running mechanics, running economy and perceived comfort by Ken Van Alsenoy (14150559)

    Published 2022
    “…Immediately after completion of a repeated-sprints exercise (8 × 5 s treadmill sprints, rest = 25 s), these run tests were replicated. …”
  18. 758

    Characteristics of aerosols and planetary boundary layer dynamics during biomass burning season by Muhammad Zeeshaan Shahid (18131689)

    Published 2025
    “…These elevated pollution levels over NEP (69–75.5°E, 27.4–34°N) are influenced by both meteorological conditions and anthropogenic activities. …”
  19. 759

    Evaluation and Enhancement of Triaging Services Through Quality Improvement Tools at Primary Health Care Level: A Clinical Audit Study by Ansif Pallath Majeed (17993848)

    Published 2023
    “…Compliance with the suggested time target of 5 minutes for physicians to attend medical emergencies has shown a small improvement from 48% at baseline to 55% in the re-audit. …”
  20. 760

    Energy conversion of heat from abandoned oil wells to mechanical refrigeration - Transient analysis and optimization by Mohammed Al-Khawaja (17093017)

    Published 2021
    “…Results show that at realistic and conservative conditions, the geofluid temperature considerably decreases for the first four months of operation (by an average of 30 °C) and tends to be constant after half a year of operation. …”